Garage Door Repair Chicago
Call us to get your garage door cables repair or a replacement. We will repair your broken cables. If you own a residential garage door in Chicago we are here for you. You notice one of your cables are broken or wrapped around the tube/shaft and not on the drum.
What do you do when you have a broken cable on your garage door? Your garage door will work for many years without giving any problem, many many years. But when they break what do you do? Easy call the expert garage door companies in Chicago. Victor Garage Door Chicago is probably the best option since they offer same day service and reasonably prices.
Victor Garage Door Chicago Process is as easy as S.A.P or 1,2,3..Schedule, Approve, Pay.
Call them to make an appointment, Approve the work before is done, Pay with what si convenient.
If you have never worked on a garage door before, then you should hire someone who has. The springs are powerful and dangerous. You risk serious injury. If you are determined to do it anyway, then download an installation manual for your door or one that looks like it. There you will find instructions and illustrations that will help you.
Garage Door cable repairs in Chicago involves the service call to cover travel expenses, parts(cables and sometimes other hardware needed to be replaced) and labor.
The total cost from most companies in Chicago for a residential standard 7' high garage door is between $140-$240
The cable repair also includes an inspection, maintenance and a 2-year warranty from most companies.
Garage door repair cable is needed for a couple of reasons:
The garage door cable on one side snaps near the top of the door. The door starts making funny noises when opened and closed. And when it closes one side sits higher than the other, with a gap between the bottom of the door and the floor. You can get r a new cable and installed it youryself but it can be extremely dangerous since they are connected to your spring system.
The most important thing is to get it wound properly on the take-up spool so it doesnβt bind as it rolls up and unrolls. If itβs binding, it will make a loud snap or pop as it raises and lowers.
You may need to reposition the drum on the shaft connected to the long horizontal spring at the top of the garage door. This is because the new cable has not stretched like the old one, and may cause the door to sit higher on the new side. Please note that it is not safe to use your garage door opener when the door has a broken cable. This could cause additional problems too your door and opener.
There is usually a set screw of some sort on the spool that you can adjust to get the door to sit level.
The problem is if the fully wound spring needs to be adjusted. (the video below gets around this problem by not actually working on the spring, and working on the door when is is in the up position, when the spring has about one wind of tension on it) Many people attempt work on springs with improvised tools such as screw drivers.
A coworker in the garage door trade attempted such a procedure. His screwdriver slipped and it was driven through his hand. Working on the garage door torsion springs without proper tools and knowledge is highly dangerous.
Look carefully to determine why the cable came off - rollers out of alignment, anchor bracket coming loose, etc. I am surprised to see that Chads answer is no longer on this question. This video explains what to do when the cable comes off. Later it shows the repairman adjusting the spring tension. He does not give details. Please do not attempt to adjust the spring tension. It is very dangerous unless you know exactly what you are doing. If not call the garage door spring repair professional.
Replacing a frayed or broken garage door cable is not very difficult to do. The job safely it's important to understand how a garage door extension spring lifting system opens the door at the bottom corners of the door there are bottom brackets attached to the side of the bottom bracket is the end loop of lifting cable.
The cable runs parallel with the vertical track loops over the pulley at the top of the door around a pulley at the end of the extension spring and attached to the horizontal track when a door is closed the garage door Springs are stretched and there's a lot of tension on the cables,
Springs, and Hardware.
1. Disconnect the power from the opener you may have to turn a breaker off or pull a fuse disconnect the door from the opener.
2. Raise the door manually if one of the cables is broken with the door from the broken cable side make sure that the broken cable doesn't get caught on anything as the door is opened some doors are very heavy and you may need help to lift the door this 8x7 door weighs 90 pounds you'll be disconnecting the lifting springs for the door to prevent the door from crashing down and breaking or hurting you.
3. Clamp a pair of vise grips onto the track just below the lowest roller on the garage door when the door is open the springs are compressed they've done their job and lifted the door and there is now very little the tension left on the cables hardware and springs with the opener disconnected the power off and a clamp at the bottom of the garage door it's safe to remove the rest of the tension from the lifting table you'll find a s hook that is hooked into the frame of the door mark the position and remove the hook.
4. Remove the garage door cable loop from the bottom bracket of the door take note of how the cable goes through the pulley fork that's attached to the end of the extension spring then feed the end of the cable through the pulley fork pre-made cables can be purchased you'll need to know the height of the door to get the correct length typical residential door Heights are seven or eight feet.
5. Measure the existing cable they have different thicknesses if you think that the existing cable is the the wrong size consult the door owner's manual or the door manufacturer measure the old and new cables.
6. Clamp a pair of vise grips onto the correct length you don't use the large hole that's for the S hook.
7. Feed the new cable through the pulley fork thread the cable over the top of the pulley put the loop around the bottom bracket of the door hold the end of the lift cable and give it a little tug double-check that the cable loose through the pulley at the end of the spring.
8. Reattach the s hook to the the horizontal frame then repeat this process for the cable on the other side of the door after both cables are replaced double check that the cable loops are connected to both plates at the bottom of the door and that the cables are correctly exceeded in the grooves of all four pulleys
9. Remove the vice grips from underneath the bottom the garage door roller of the door manually open and close the door and check to see that the cables or boys don't catch or bind on anything reconnects the door to that opener reconnect power
I hope you found this video is helpful a thumbs up are always appreciated click on the channel name know-how now to see other videos an
Service are:
garage door repair chicago and we provide all types of garage door services including garage door repair cable.
Garage Door Cable repair
fix garage door cable in chicago
Copyright Β© 2022 Garage Door Repairs Chicago - All Rights Reserved.
sapgaragedoor